FireplaceXtrordinair Indoor Fireplace 98500507 User Manual

FPX 32 DVS Artisan Face  
Charcoal 98500507  
Antique Copper 98500508  
Antique Nickel 98500509  
Compatibility  
DVS Insert  
• 31 DVI Insert  
NOTE: On newer units (2008 or later), leave the glass on and move the face connector to the forward  
position (see illustration below). For older units, remove the glass.  
Remove the face connector bracket  
from the heater (on both sides).  
Re-attach the face connector to the  
heater using the forward mounting holes.  
Face Connector  
Bracket  
Warnings  
Plated Surfaces Warning:  
Denatured  
Alcohol  
Any marks left on the optional plated surface may become etched-in by the heat of the  
appliance. Use denatured alcohol and a soft cloth to clean.  
Soft Cloth  
Copper Surfaces Warning:  
Anti-  
Use the included anti-oxidizer to clean the optional copper surface. See the included instruction  
sheet for full details.  
Oxidizer  
Soft Cloth  
Warning:  
Make sure the heater has fully cooled prior to conducting service.  
Packing List  
10-24 Nuts  
1/4-20  
Screws  
Page 1 of 4  
17601079 - 5/10/10  
© Travis Industries, Inc.  
 
FPX 32 DVS Artisan Face  
Charcoal 98500507  
Antique Copper 98500508  
Antique Nickel 98500509  
Face Installation  
Attach the face using the four  
bolts included with the face.  
Adjustable  
Wrench  
Make sure the door does  
not open while installing.  
Page 3 of 4  
17601079 - 5/10/10  
© Travis Industries, Inc.  
 
FPX 32 DVS Artisan Face  
Charcoal 98500507  
Antique Copper 98500508  
Antique Nickel 98500509  
Opening the Control Door  
Warning:  
The face becomes very hot during operation. Use the included handle open the control and  
take care to not touch any of the hot surfaces.  
Use the pull tool  
on either side to  
disengage the  
hinges.  
Pull Tool  
(included  
with face)  
Control Door  
Note how the hooks on the tool insert  
into the triangle-shaped holes.  
When removing the  
pull tool, make sure  
it does not damage  
the hearth.  
Adjusting the Control Door  
The control is adjsuted at the factory. See the directions below if further adjustment is necessary.  
Bullet Catch  
Back of Face (with face removed)  
Back of Bullet  
Catch  
These two nuts hold the  
bullet catch assembly.  
If the top of the control  
door is not aligned,  
these nuts can be  
loosened to re-align the  
bullet catch assembly.  
Access  
Panel  
Adjust this nut to tighten  
or loosen the friction of  
the hinge.  
This bullet-shaped device holds the control door  
upright. To tighten or loosen the catch, simple  
rotate it (it is threaded inside the assembly).  
Page 4 of 4  
17601079 - 5/10/10  
© Travis Industries, Inc.  
 

EdgeStar Freezer Upright Freezer User Manual
Eiki Projector LC 6000UL User Manual
Eiki Projector LC 6000 User Manual
Eizo Computer Monitor FlexScan T561 User Manual
Festool Sander PI567696 User Manual
Fujitsu Scanner 15C User Manual
GE Dehumidifier ADEH50 User Manual
GE Door 19217 User Manual
Gigabyte Network Card GV N57128DE User Manual
Gitzo Camcorder Accessories GT2942L User Manual